Pesquisar este blog

Translate

quarta-feira, 25 de abril de 2012

FDA - Nanotechnology by Food



Draft Guidance for Industry: Assessing the Effects of Significant Manufacturing Process Changes, Including Emerging Technologies, on the Safety and Regulatory Status of Food Ingredients and Food Contact Sub

Contains Nonbinding Recommendations
Draft - Not for Implementation
April 2012

This guidance is being distributed for comment purposes only.
Although you can comment on any guidance at any time (see 21 CFR 10.115(g)(5)), to ensure that the agency considers your comment on this draft guidance before it begins work on the final version of the guidance, submit electronic or written comments on the draft guidance within 90 days of publication in the Federal Register of the notice announcing the availability of the draft guidance. Submit electronic comments to http://www.regulations.gov. All comments should be identified with the docket number listed in the notice of availability that publishes in the Federal Register. Submit written comments to the Division of Dockets Management (HFA-305), Food and Drug Administration, 5630 Fishers Lane, rm. 1061, Rockville, MD 20852.
For questions regarding this draft document contact the Center for Food Safety and Applied Nutrition (CFSAN) at 240-402-1200.
U.S. Department of Health and Human ServicesFood and Drug Administration
Office of Foods
Center for Food Safety and Applied Nutrition
April 2012

Contains Nonbinding Recommendations
Draft - Not for Implementation
Available in PDF (148 KB).

Table of Contents

  1. Introduction
  2. Regulatory Framework for Food Substances
    1. Industry's Responsibility Regarding the Safe and Lawful Use of Food Substances
    2. Food Additive Statutory and Regulatory Provisions
    3. Color Additive Statutory and Regulatory Provisions
  3. Safety Assessment of a Food Substance
    1. Identity
    2. Technical Effect
    3. Self-limiting Levels of Use
    4. Dietary Exposure and Safety Studies
    5. Manufacturing Processes, including Nanotechnology
  4. Discussion
    1. Considerations for Assessing the Impact of a Significant Manufacturing Process Change on the Safety and Regulatory Status of a Food Substance
    2. Recommendations for Assessing the Effect of a Significant Manufacturing Process Change on the Safety and Regulatory Status of a Food Substance
  5. References
    1. Carrageenan (21 CFR 172.620)
    2. Xanthan Gum (21 CFR 172.695 and GRAS Notice No. GRN 000121)
    3. Tartaric Acid (21 CFR 184.1099 and GRAS Notice No. GRN 000187)
    1. Petition Process for Premarket Approval of a Food Additive
    2. Premarket Notification Program for a Food Contact Substance
    3. "Threshold of Regulation" Program for a Substance Used in a Food Contact Article
    4. Program to Notify FDA of a Determination That a Use of a Substance is Generally Recognized as Safe
    5. Petition Process for Listing a Color Additive
       

Draft Guidance for Industry1
Assessing the Effects of Significant Manufacturing Process Changes, Including Emerging Technologies, on the Safety and Regulatory Status of Food Ingredients and Food Contact Substances, Including Food Ingredients that are Color Additives

This draft guidance, when finalized, will represent the Food and Drug Administration's (FDA’s) current thinking on this topic.  It does not create or confer any rights for or on any person and does not operate to bind FDA or the public.  You can use an alternative approach if the approach satisfies the requirements of the applicable statutes and regulations.  If you want to discuss an alternative approach, contact the FDA staff responsible for implementing this guidance.  If you cannot identify the appropriate FDA staff, call the telephone number listed on the title page of this guidance.

I. Introduction

This document provides guidance to manufacturers of food ingredients and food contact substances (FCSs), and end users2 of food ingredients and FCSs, including food ingredients that are color additives.  In the remainder of this document, we use the term “food substance” as a general term addressing food ingredients and FCSs.
This guidance is intended to describe the factors you should consider when determining whether a significant change in manufacturing process for a food substance already in the market:
  • Affects the identity of the food substance;
  • Affects the safety of the use of the food substance;
  • Affects the regulatory status of the use of the food substance; and
  • Warrants a regulatory submission to FDA.
As with all food substances, this guidance also is intended to recommend that you consult with us regarding a significant change in manufacturing process for a food substance already in the market, irrespective of your conclusion about whether that change affects the safety or regulatory status of the food substance.  It is prudent practice for you to do so, particularly when the change in manufacturing process involves emerging technology.  Food substances may be used in a wide array of products manufactured, distributed and sold at retail by a large number of firms. The consequences (to consumers and to the food industry) of broadly distributing a food substance that is later recognized to present a safety concern have the potential to be significant.
Any manufacturing change has the potential to be significant, and this remains true for changes or novel products, involving nanotechnology. Alterations in particle size distribution on the nanometer scale,3 which alter the physical and/or chemical properties of food ingredients and FCSs, can sometimes be significant manufacturing changes.  The discussion in this document of nanotechnology4 -- in particular, intentional alterations of particle size distribution on the nanometer scale -- primarily addresses circumstances in which there has been a manufacturing change to a food substance already used in food. 
FDA has previously released, and periodically updates, guidance documents that address data recommendations to support the safety of uses of food substances not previously authorized.  These guidances, listed as References 6, 7, and 8, respectively, are: Guidance for Industry - Recommendations for Submission of Chemical and Technological Data for Direct Food Additive PetitionsGuidance for Industry - Color Additive Petitions. FDA Recommendations for Submission of Chemical And Technological Data On Color Additives For Food, Drugs Or Cosmetics; and Guidance for Industry - Preparation of Premarket Submissions for Food Contact Substances: Chemistry Recommendations.  These documents are available on FDA's website.  We recommend that manufacturers consult these guidance documents before preparing a submission to FDA.  The discussions and recommendations in this guidance document regarding appropriate pathways to gain premarket review by FDA may also be applicable to new uses of food substances. 
This draft guidance is not applicable to other products regulated by FDA, including over-the-counter and prescription drugs.  FDA’s current thinking concerning nanomaterials for food uses, which is explained below, is not intended to provide guidance to manufacturers or end users about the use of nanomaterials in any non-food article regulated by FDA.  This guidance is also not intended to provide guidance to manufacturers or end users of color additives intended for use in non-food products (e.g., products that are cosmetics, drugs or medical devices).
FDA’s guidance documents, including this guidance, do not establish legally enforceable responsibilities.  Instead, guidances describe the Agency’s current thinking on a topic and should be viewed only as recommendations, unless specific regulatory or statutory requirements are cited.  The use of the word shouldin Agency guidances means that something is suggested or recommended, but not required.
  

II. Regulatory Framework for Food Substances


A. Industry’s Responsibility Regarding the Safe and Lawful Use of Food Substances

Under section 402 of the Federal Food, Drug, and Cosmetic Act (the Act), food shall be deemed to be adulterated if, among other things:
  • The food bears or contains an added poisonous or deleterious substance which may render it injurious to health (section 402(a)(1));
  • The food bears or contains any food additive that is unsafe within the meaning of section 409 of the Act (section 402(a)(2)(C)); or
  • The food bears or contains a color additive that is unsafe within the meaning of section 721(a) of the Act (section 402(c)).
Under section 301 of the Act, the following acts (among others) and the causing thereof are prohibited: 
  • The introduction or delivery for introduction into interstate commerce of any food that is adulterated (section 301(a));
  • The adulteration of any food in interstate commerce (section 301(b)); and
  • The receipt in interstate commerce of any food that is adulterated, and the delivery or proffered delivery thereof for pay or otherwise (section 301(c)).
Under sections 402 and 301 of the Act, it is the responsibility of both the manufacturer and the end user of a food substance to ensure that the use of the food substance is safe and lawful.  Remedies for violations of the Act include seizure, injunction, and criminal prosecution.5 

B. Food Additive Statutory and Regulatory Provisions

In 1958, Congress enacted the Food Additives Amendment to the Act; in 1997, Congress enacted the Food and Drug Administration Modernization Act (FDAMA) as another amendment to the Act.  Briefly, the Food Additives Amendment and FDAMA:
  • Define the term “food additive” (section 201(s)) to:
    • Broadly include any substance, the intended use of which results or may reasonably be expected to result, directly or indirectly, in its becoming a component or otherwise affecting the characteristics of food; and
    • Exclude (among other things) substances that are generally recognized, among experts qualified by scientific training and experience to evaluate their safety (“qualified experts”), as having been adequately shown through scientific procedures (or, in the case of a substance used in food prior to January 1, 1958, through either scientific procedures or through experience based on common use in food) to be safe under the conditions of their intended use;
  • Establish a premarket approval process for food additives and for food contact substances, whether or not they are food additives  (sections 409(b) - (h));
  • Provide that food shall be deemed to be adulterated if it is, or bears or contains, any food additive that is unsafe within the meaning of section 409 (section 402(a)(2)(C));6
  • Establish that a food additive shall, with respect to any particular use or intended use of such additive, be deemed to be unsafe for the purposes of the application of section 402(a)(2)(C) unless:
    • It and its use or intended use conform to the terms of an exemption which is in effect pursuant to section 409(j) (section 409(a)(1));
    • There is in effect, and it and its use or intended use are in conformity with, a regulation issued under section 409 prescribing the conditions under which such additive may be safely used (section 409(a)(2)); or
    • In the case of a food additive that is a FCS, there is:
      • in effect, and such substance and the use of such substance are in conformity with, a regulation issued under section 409 prescribing the conditions under which such additive may be safely used (section 409(a)(3)(A)); or
      • a notification submitted under section 409(h) that is effective (section 409(a)(3)(B)).
  • Provide that while a regulation relating to a food additive, or a notification under section 409(h)(1) relating to a food additive that is a FCS, is in effect, and has not been revoked pursuant to section 409(i), a food shall not, by reason of bearing or containing such a food additive in accordance with the regulation or notification, be considered adulterated under section 402(a)(1).
A food substance is not subject to the premarket approval requirements of section 409 of the Act if its safety is generally recognized by qualified experts (section 201(s) of the Act).  A determination that a particular use of a substance is GRAS (unless established by common use prior to 1958) requires both technical evidence of safety and a basis to conclude that this technical evidence of safety is generally known and accepted (i.e., general recognition of safety).  21 CFR 170.30.  In contrast, a determination that a particular use of a food additive is safe via premarket approval requires only technical evidence of safety.  
Thus, “a GRAS substance is distinguished from a food additive on the basis of the common knowledge about safety of the substance for its intended use, rather than on the basis of what the substance is or the types of data and information that are necessary to establish its safety” (62 FR 18938 at 18940; April 17, 1997).  “To establish [general] recognition, the proponent must show that there is a consensus of expert opinion regarding the safety of the use of the substance” (62 FR at 18939). 
Regulations identifying GRAS conditions of use for certain substances in food are in Part 182 and regulations affirming the GRAS status of the use of some food ingredients and food contact substances are in 21 CFR Parts 184 and 186, respectively.  Regulations prescribing conditions under which substances affirmed as GRAS may be safely used in food predicate usage under conditions of good manufacturing practice (GMP) (21 CFR 182.1(b) and 184.1(b)).  A food ingredient that is identified or affirmed as GRAS must also meet the requirements in 21 CFR 170.30(h).
Under the Food Additives Amendment, a food substance that is GRAS for a particular use may be marketed for that use without our review and approval. However, when a use of a food substance is not GRAS (and other exclusions provided under section 201(s) of the Act, such as for a pesticidal substance (201(s)(2), are inapplicable), that use of the substance is a food additive use subject to the premarket approval mandated by the Act. Where a use of such a food substance is marketed without premarket approval we can take enforcement action to stop distribution of the food substance and foods containing that food substance on the grounds that such foods are adulterated because they are or contain an unlawful food additive.
We have established regulations defining terms associated with food additives and food contact substances (21 CFR 170.3).  Under 21 CFR 170.3(i), “safe” or “safety” means that there is a reasonable certainty in the minds of competent scientists that the substance is not harmful under the intended conditions of use. This definition of “safe” or “safety” provides that it is impossible in the present state of scientific knowledge to establish with complete certainty the absolute harmlessness of the use of any substance. Under the regulatory framework, safety may be determined by scientific procedures or by general recognition of safety. In determining safety under either route, the following factors shall be considered:
  • The probable consumption of the substance and of any substance formed in or on food because of its use (21 CFR 170.3(i)(1));
  • The cumulative effect of the substance in the diet, taking into account any chemically or pharmacologically related substance or substances in such diet (21 CFR 170.3(i)(2)); and
  • Safety factors which, in the opinion of experts qualified by scientific training and experience to evaluate the safety of food and food ingredients, are generally recognized as appropriate (21 CFR 170.3(i)(3)).
Regulations prescribing conditions under which substances approved as food additives, listed as GRAS, or affirmed as GRAS may be safely used predicate usage under conditions of good manufacturing practice (21 CFR 172.5, 182.1(b), 184.1(b)), which include the following:
  • The quantity of the substance added to food does not exceed the amount reasonably required to accomplish its intended physical, nutritive, or other technical effect in food; and
  • Any substance intended for use in or on food is of appropriate food grade and is prepared and handled as a food ingredient.
We have established (or proposed to establish) regulatory submission programs regarding several categories of food substances relevant to section 409 of the Act. We describe the principal regulatory submission programs in Appendix 2 of this document. >We have provided guidance to industry on administrative aspects of these regulatory submissions (Refs. 3-5).

C. Color Additive Statutory and Regulatory Provisions

In 1960, Congress enacted the Color Additive Amendments to the Act.  Briefly, the 1960 Color Additive Amendments:
  • Define the term “color additive” (section 201(t));
  • Establish a listing and certification process for color additives (sections 7217 (b) - (e));
  • Amend the food adulteration provisions of the Act to deem adulterated any food that is, or bears or contains, any color additive that is unsafe within the meaning of section 721 (section 402(c));
  • Establish that a color additive shall, with respect to any particular use or intended use of such additive, be deemed to be unsafe for the purposes of the application of section 402(c) unless:
    • There is in effect, and such additive and such use are in conformity with, a regulation issued under section 721(b) listing such additive for such use, including any provision of such regulation prescribing the conditions under which such additive may be safely used (section 721(a)(1)(A)); and
    • Such additive either (i) is from a batch certified, in accordance with regulations issued pursuant to section 721(c), for such use, or (ii) has, with respect to such use, been exempted by the Secretary from the requirement of certification (section 721(a)(1)(B)); or
    • Such additive and such use thereof conform to the terms of an exemption which is in effect pursuant to subsection (f) of this section (section721(a)(2)); and
  • Provide that, while there are in effect regulations under sections 721(b) and (c) relating to a color additive or an exemption pursuant to section 721(f) with respect to such additive, an article shall not, by reason of bearing or containing such additive in all respects in accordance with such regulations or such exemption, be considered adulterated within the meaning of section 402(a)(1).
There is no GRAS provision for color additives, and all uses of color additives must be approved as safe by FDA prior to marketing.
We have established regulations defining terms associated with color additives (21 CFR 70.3).  Under 21 CFR 70.3(i), safe means that there is convincing evidence that establishes with reasonable certainty that no harm will result from the intended use of the color additive.
We describe our program for a petition process for color additives in Appendix 2 of this document.  We have provided guidance to industry on administrative aspects of the color additive petition process (Ref. 3).

III. Safety Assessment of a Food Substance

As described in our existing guidance documents (Refs. 6-11), an assessment of the safety of a food substance generally involves an evaluation of information about its safety and functionality including all studies and tests of a food additive on animals and humans and all studies and tests of a food additive for identity, stability, purity, potency, performance, and usefulness (21 CFR 171.1(h)(4)).  We briefly describe each of these aspects in sections III.A through III.D of this document. 
Our regulations and guidance documents on food substances generally include the manufacturing process as part of the information describing the identity of a food substance.  However, because the purpose of this document is directed to assessing the effect of a change in manufacturing process on the safety and regulatory status of a food substance, in this document we discuss the role of the manufacturing process in a safety assessment in a separate section (see section III.E).

A. Identity

The identity of a food substance is usually described in terms of information such as:
  • Its name (including chemical name and a common or trade name);
  • Applicable identification number, such as a Chemical Abstracts Service Registry Number (CAS Reg. No.) or an Enzyme Commission Number;
  • Applicable chemical formula(e);
  • Source (when a food substance is of natural biological origin);
  • Quantitative composition;
  • Impurities and contaminants; and
  • Physical and chemical properties and specifications for these properties (e.g., melting point, boiling point, specific gravity, refractive index, optical rotation, pH, solubility, reactivity, particle size, and chromatographic, spectroscopic or spectrometric data  that can be used as a “fingerprint” for identification).
The specifications of identity of a food substance are an important component of the safety assessment and are used to establish safe conditions of use in food.  Changes in the physical and chemical properties of a food substance can influence its technical effect in food or food contact materials and can influence the nutritional or toxicological properties of the food substance. 
In sections III.B through III.D of this document, we explain how the identity of a substance (particularly its physical and chemical properties) can affect the technical effect, self-limiting levels of use, and dietary exposure and the level at which a food substance exhibits adverse effects.
  

B. Technical Effect

Substances may be added to food to accomplish a variety of technical effects in food.  Examples of physical or technical functional effects for which food substances may be added include antimicrobial agent, humectant, flavoring agent, surface-active agent, stabilizer and thickener (21 CFR 170.3(o)).
The physical and chemical properties of a food substance generally impact its technical effect and significant changes to a food substance’s technical or functional effect may result in conditions of use that are not authorized.  For example:
  • If an isolated or chemically processed fiber is intended for use as a replacement for part of the flour used in baked goods, its ability to swell due to high water absorption or to bind physiologically important ions may be relevant to determining the appropriate level of the fiber in baked goods. 
  • The color of a color additive may change simply by reducing the particle size of the substance, as seen with gold particles which display a range of colors dependent on the size of the particle (Ref. 12).

C. Self-limiting Levels of Use

When a substance is added to food above its technologically self-limiting level, the food may become unpalatable, unappealing or otherwise unfit for consumption.  For example, the taste associated with many chemically defined flavoring substances limits the levels at which the flavoring substances can be used.  A self-limiting level of use can help ensure safety if, for example, any known toxic effects would only occur at levels that exceed the self-limiting use levels.
The physical and chemical properties of a food substance can affect the level at which it becomes self-limiting from a food technology or palatability perspective.  For example, the self-limiting level of a flavoring agent may be affected by the particle size of the flavoring agent – e.g., if smaller particles are absorbed more quickly than larger particles.  Significant alterations to physical or chemical properties of a food substance and any associated changes to the self-limiting use levels are important considerations in the safety assessment and in establishing the conditions of safe use of the food substance. 

D. Dietary Exposure and Safety Studies

Studies conducted in vitro or in vivo can identify adverse effects that could occur from acute exposure to, or chronic consumption of, a food substance.  In most cases, such effects are dose-dependent.  A key determinant in the safety evaluation of a food substance is the relation of its probable human intake to the level at which adverse effects are observed in toxicological studies (Ref. 9). In many cases, determining the amount of a food substance that can safely be consumed involves application of a “safety factor” (as described in 21 CFR 170.3(i)) to a “no observed adverse effect level” for the most sensitive indicator of an observed adverse effect. 
Alterations in the physical and chemical properties of a food substance can affect its bioavailability through altered absorption, distribution, metabolism and excretion of the substance in the body.  Such changes in the substance’s biological interactions can affect the level at which toxic effects may occur (Ref. 13).  For example, the particle size of a food substance may affect its ability to be absorbed by the body or to migrate from food packaging into food.  In such circumstances, safety studies conducted with a food substance manufactured as relatively large particles may have little relevance to the safety of that food substance when manufactured in a significantly smaller particle size. 
FDA generally recommends that manufacturers and end users follow our toxicology guidance, (see, e.g., Refs. 9 and 10) when preparing their comprehensive toxicology profile.  There are instances where a compound, or a class of compounds, has known toxicological endpoints that are not specifically addressed through the standard guidelines, e.g., the potential risk of alloimmunization8 posed by exposure to human proteins.  In such cases, it is the responsibility of manufacturers and end users to develop appropriate protocols to address particular safety issues.  Historically, such persons have been advised that they should consult with FDA on the safety issues related to the intended use. 

E. Manufacturing Processes, including Nanotechnology

The manufacturing process of a food substance is considered for the purposes of safety assessment only insofar as it may affect the properties and safety of the finished product.  As explained below, the manufacturing process may affect the identity of the food substance or its conditions of use.  The manufacturing process may also affect the purity of a food substance, such as the amount of impurities and contaminants in the food substance.  For example:
  • An enzyme preparation that is manufactured from an animal source and contains the enzyme chymosin as its principal enzyme component (§ 184.1685(a)(1)) is chemically different from an enzyme preparation that is manufactured from a microbial source and contains the enzyme chymosin as its principal enzyme component (§ 184.1685(a)(2)).  Although they both contain an enzyme component that catalyzes the same chemical reaction, they also contain distinctly different constituents derived from the production organism and constituents derived from the manufacturing process (e.g., components of the fermentation media or the residues of processing aids).
  • Including an activated carbon treatment of fish oil can reduce levels of polycyclic aromatic hydrocarbons (PAHs) that can be present in fish oil obtained from fish from a natural marine environment (Ref. 14).
  • The catalyst for the production of a food contact polymer may affect the chemical identity or the amounts of residual contaminants that may migrate from the polymer to food.
  • The particle size distribution of a food substance may affect its ability to be absorbed by the body or to migrate from food packaging into food (Ref. 13).   
Nanotechnology is an emerging technology that can be used in food manufacturing.  Consistent with the recommendations in the 2007 Task Force Report (Ref 1), we are issuing guidance to discuss nanotechnology in this section -- in particular, intentional alterations of particle size distribution on the nanometer scale -- to address circumstances in which there is a manufacturing change to a food substance already used in food.  FDA considers food manufacturing processes that involve nanotechnology in the same manner as any other food manufacturing technology.  Although traditionally manufactured food substances can sometimes include particles with size distributions that extend into the nanometer range, recent advances in technology can allow the intentional production of food substances with particle size distributions more fully in the nanometer range, resulting in new properties not seen in traditionally manufactured food substances. 
The application of nanotechnology may result in product attributes that differ from those of conventionally-manufactured products, and thus may merit examination.  However, FDA does not categorically judge all products containing nanomaterials or otherwise involving application of nanotechnology as intrinsically benign or harmful. Rather, for nanotechnology-derived and conventionally-manufactured food products alike, FDA considers the characteristics of the finished product and the safety of its intended use.  FDA recently issued a draft guidance to industry on the agency’s considerations related to nanotechnology (Ref. 2).  FDA’s consideration of nanotechnology applications in food substances in this document is consistent with the agency’s draft guidance (Ref. 2) and with the broader federal guidance on regulatory oversight of emerging technologies (Ref. 15) and nanotechnology (Ref. 16).
As with any other manufacturing technologies applied to food, nanotechnology and other emerging technologies may introduce issues that warrant additional or different evaluation during a safety assessment of a food substance (Ref. 1).  For example, so-called nano-engineered food substances can have significantly altered bioavailability and may, therefore, raise new safety issues that have not been seen in their traditionally manufactured counterparts (Ref. 13). There is debate regarding the appropriate testing to judge the safety of food substances where physical and chemical properties are manipulated by engineering particle size distributions in the nanometer range, in some instances to intentionally manipulate the biological properties, as also noted by some scientific authorities (Refs. 1, 13, 17 and 18).  Guidance and extrapolation from data on traditionally manufactured food substances can generally be accomplished only on a case-by-case basis.  When a food substance is manufactured to include a particle size distribution shifted more fully into the nanometer range, safety assessments should be based on data relevant to the nanometer version of the food substance.  Where nano-engineered food substances have new properties, additional or different testing methods may be necessary to determine the safety of the food substance.  For example, particle size, surface area, aggregation/agglomeration, or shape may impact absorption, distribution, metabolism and excretion (ADME) and potentially the safety of the nano-engineered food substance (Refs. 13, 17).  In such cases, it may be necessary to further examine the effects of a change in these properties, including any effects on the bioavailability of the food substance and its transport across the gut. The variation in biological activity that may result from engineering food substances in the nanometer range may raise questions about the applicability of traditional safety tests for these materials.  Thus, as with any studies to support the safety of food substances, studies to establish the safety of food substances manufactured using nanotechnology should have been appropriately validated for these materials.  
FDA has issued guidance to industry to provide recommendations on chemical and technological data that we consider necessary for the evaluation of food additives, color additives, and food contact substances (Ref. 6-8).  In those documents, we discuss the relevance of particle size in submitting safety assessments for food additive petitions, color additive petitions, and food contact notifications.  We encourage manufacturers to refer to those documents for any questions related to safety data submissions to the agency. FDA continues to welcome consultations with industry as an approach to ensuring that food developed using new technologies will be safe.  For example, we encourage developers of new plant varieties developed using modern techniques of biotechnology to consult with us (Ref. 19).
Some Food Contact Notifications (FCNs) (e.g., FCNs 716 and 818) have included information describing the use of a food contact substance with particle sizes in a nanometer range.  To date, we have not, to our knowledge, received food or color additive petitions, or GRAS affirmation petitions or notices, for any uses of food ingredients with a particle size distribution fully in the nanometer range.
In summary, safety assessments should be as rigorous as possible and should be based on data relevant to the version of the food substance intended for use. . Where safety questions are raised that experts would need additional data to resolve and such data are not generally recognized, the general recognition of safety criteria for GRAS would not be satisfied for the use of such food ingredients or FCSs.  At this time, we are not aware of any food ingredient or FCS intentionally engineered9 on the nanometer scale for which there are generally available safety data sufficient to serve as the foundation for a determination that the use of a food ingredient or FCS is GRAS.

IV. Discussion

 

A. Considerations for Assessing the Impact of a Significant Manufacturing Process Change on the Safety and Regulatory Status of a Food Substance

Before any food substance is marketed, it is the subject of a safety assessment such as we describe in section III of this document.  Over time, the manufacturing process for a food substance may evolve – e.g., to incorporate a more efficient catalyst, to replace an expensive solvent with a more cost-effective solvent, or to introduce a treatment to reduce the presence of contaminants such as lead.
Some of these changes in a manufacturing process may be considered significant.  It is these significant changes in manufacturing process that are the subject of this guidance.  Examples of significant changes in manufacturing process may include:
  • A change in one or more starting materials;
  • A change in the concentration of starting materials;
  • A change in catalyst;
  • A change in the source microorganism (including a change in strain) used for a food substance derived from fermentation of a microorganism; and
  • A change in food manufacturing or ingredient technology, such as the use of emerging technologies that affect the particle size distribution of a food substance.
We expect that there will be circumstances where a significant change in manufacturing process impacts the safety, the regulatory status, or both, of a food substance.   In such circumstances, a new regulatory submission may be necessary to clearly establish the conditions under which the food substance, manufactured by a new process, is safe and lawful.  In the case of emerging technologies, a manufacturing process may alter the identity or intended use of the food substance and a new authorization may be required.
For food substances already in the marketplace, a significant change in the manufacturing process of the food substance can affect the safety of the food substance.  Section III of this document explains some of the ways in which a significant change in the manufacturing process for a food substance can impact its safety. 
A significant change in the manufacturing process of a food substance already in the market can also affect the identity or conditions of use of a food substance, rendering the use of the food substance not within the scope of a food additive regulation; a GRAS listing or affirmation in 21 CFR; an effective food contact notification; or an existing determination of GRAS status. When determining whether an existing regulation, FCN, or GRAS determination applies to the use of a food substance that has been subjected to a significant change in manufacturing process, it is important to consider the identity and intended conditions of use of the food substance manufactured by the new process in comparison to the identity and intended conditions of use of the food substance that was the subject of the original approval, notification, or determination.
For example, the characteristic properties may not match the information considered in a determination of GRAS status, rendering the previous determination of GRAS status inapplicable. 
There also may be cases where it simply is not clear whether the use of a food substance complies with an existing regulation.  It is prudent practice for manufacturers and end users of food substances to take appropriate steps to ensure that the use of the substance satisfies all regulatory requirements.
Appendix 1 provides three specific examples of situations in which the Agency reconsidered the regulatory status of the use of a food substance and concluded that a significant change in manufacturing process did not negatively impact safety.  In these specific examples, we reviewed the data and factual information supporting a conclusion that the intended use of the food substance continued to be safe and lawful after the change in manufacturing process.  In the first situation, we initially requested that a new food additive petition be submitted, and then rescinded this request after consideration of applicable data and information outside the context of a food additive petition. In the remaining two situations, we reviewed a new regulatory submission from the sponsor of the food substance manufactured through a new process.  

B. Recommendations for Assessing the Effect of a Significant Manufacturing Process Change on the Safety and Regulatory Status of a Food Substance

1.  The use of food substances that are the subject of a food additive or color additive regulation in 21 CFR10
We recommend that, whenever there has been a significant change in manufacturing process for the use of a food substance that is the subject of a food additive or color additive regulation in 21 CFR, you:
  • Determine what changes have been made to the identity of the food substance as a result of the change in manufacturing process, including its physicochemical structure and properties, purity, and impurities;
  • Taking into account any impact of the change in identity of the food substance, conduct a safety assessment for the use of the food substance, including characteristic properties such as physicochemical structure and properties, purity, impurities, bioavailability, or toxicity;
  • Consider whether the use of the food substance is authorized under a food additive or color additive regulation. Relevant to such a determination are the identity of the food substance and its conditions of use described in the administrative record for a substance subject to a food additive or color additive regulation.  For example, the food substance would not be within the scope of a regulation where:
    • The identity of, manufacturing process for, or the conditions of use of the food substance do not comply with a regulation; or
    • The food substance is not of appropriate food grade as a result of impurities introduced into the food substance by the change in manufacturing process;
  • Consult with us about your conclusions about the impact of the significant manufacturing change on the safety and regulatory status of the use of the food substance; and
  • Make an appropriate regulatory submission to FDA as circumstances warrant.
2.  The use of food substances that are affirmed or identified as GRAS in 21 CFR
We recommend that, whenever there has been a significant change in manufacturing process for a food substance that is the subject of a GRAS affirmation or identified as GRAS in 21 CFR, you:
  • Determine what changes have been made to the identity of the food substance as a result of the change in manufacturing process, including its physicochemical structure and properties, purity, and impurities;
  • Taking into account any impact of the change in identity of the food substance, conduct a safety assessment for the use of the food substance, including characteristic properties such as physicochemical structure and properties, purity, impurities, bioavailability, or toxicity; 
  • Consider whether the use of the substance is within the scope of a GRAS affirmation or identification as GRAS in 21 CFR. Relevant to such a determination are the identity of the food substance and its conditions of use described in the administrative record for a substance affirmed or identified as GRAS.  For example, it would not be where:
    • The identity of, manufacturing process for, or the conditions of use of the food substance are significantly different from those of the substance affirmed or identified as GRAS; or
    • The food substance is not of appropriate food grade as a result of impurities introduced into the food substance by the change in manufacturing process;
  • Consult with us about your conclusions about the impact of the significant manufacturing change on the safety and regulatory status of use of the food substance; and
  • Make an appropriate regulatory submission to FDA as circumstances warrant. 
As the Agency explained in the final rule establishing the GRAS affirmation process, “a regulation affirming the GRAS status of an ingredient, must, under section 201(s) of the act, be restricted to the ingredient that has been in common use in food or that was the subject of scientific tests to determine its safety.  The burden is on the manufacturer to demonstrate that the ingredient he is using is of the same composition as the ingredient that has been traditionally used or that has been investigated by researchers.”  [41 Fed. Reg. 53600, 53604 (Dec. 7, 1976)].  Furthermore, if there is a question whether a food substance differs from the food substance identified in the regulation affirming the substance as GRAS because of a change in manufacturing process, “it is the obligation of the manufacturer to demonstrate whether the ingredient has been affirmed as, or is otherwise, GRAS” [41 Fed. Reg. at 53604]
3.  The use of food contact substances for which there is an effective Food Contact Notification
Our long-standing guidance to industry on administrative aspects of a food contact notification advises that a new notification should be submitted if substantive changes are made in the specifications for the FCS or if significant changes are made in the manufacturing method that result in substantive changes in the identity of the product or its impurities, and/or levels of impurities (Refs. 4, 8).  Consistent with our previous administrative guidance, in this guidance we recommend that, whenever there has been a significant change in manufacturing process for a food contact substance, you:
  • Determine what changes have been made to the identity of the food contact substance as a result of the change in manufacturing process, including its physicochemical structure and properties, purity, and impurities;
  • Taking into account any impact of the change in identity of the food contact substance, conduct a safety assessment for the use of the food contact substance, including characteristic properties such as physicochemical structure and properties, purity, impurities, bioavailability, or toxicity;    
  • Consider whether the substance would be within the scope of an effective FCN.  For example, it would not be within the scope of an effective FCN if:
    • The identity of or the conditions of use of the food contact substance are significantly different from those described in a previously submitted notification; or
    • The food contact substance is no longer of appropriate food grade as a result of impurities introduced into the food contact substance by the change in manufacturing process;
  • Consult with us about your conclusions about the impact of the significant manufacturing change on the safety and regulatory status of the use of the food contact substance; and
  • Make an appropriate regulatory submission to FDA as circumstances warrant. 
Altering the manufacturing process of a notified food contact substance to either produce components in the nanometer scale or increase the proportion of nanometer scale components can sometimes be a significant manufacturing change that could result in a substantive change to the specifications and/or in the identity of the food contact substance or its impurities, and/or levels of impurities.   In the event of such substantive change, FDA advises you to submit a new notification.
4. Use of a food substance for which there is an existing determination that a use of a food substance11 is GRAS
Because a significant change in the manufacturing process can affect the safety, regulatory status, or both of a food substance, we recommend that, whenever there has been a significant change in manufacturing process for a food substance that is the subject of a GRAS determination, you:
  • Determine what changes have been made to the identity of the food substance as a result of the change in manufacturing process, including its physicochemical structure and properties, purity, and impurities;
  • Taking into account any impact of the change in identity of the food substance, conduct a safety assessment for the use of the food substance, including characteristic properties such as physicochemical structure and properties, purity, impurities, bioavailability, or toxicity; 
  • Consider whether the GRAS status of the use of the food substance would be affected – for example, it would not be GRAS if:
    • The identity of, manufacturing process for, or the conditions of use of the food substance are significantly different from those described in a previous GRAS determination;
    • The manufacturing changes are so novel as to preclude general recognition of safety; or
    • The food substance is no longer of appropriate food grade as a result of impurities introduced into the food substance by the change in manufacturing process;
  • Consult with us about your conclusions about the impact of the significant manufacturing change on the safety and regulatory status of the use of the food substance; and
  • Make an appropriate regulatory submission to FDA as circumstances warrant. 
In the specific instance of nanotechnology, a food substance manufactured for the purpose of creating very small particle sizes with new functional properties likely would not be covered by an existing GRAS determination for a related food substance manufactured without using nanotechnology.  A determination that a particular use of a substance is GRAS (unless established by common use prior to 1958) requires bothtechnical evidence of safety and a basis to conclude that this technical evidence of safety is generally known and accepted (i.e., general recognition of safety).  At present, for nanotechnology applications in food substances, there are questions related to the technical evidence of safety as well as the general recognition of that safety, that are likely to be sufficient to warrant formal premarket review and approval by FDA, rather than to satisfy criteria for GRAS status12.
As FDA stated in the preamble to the proposed rule for the GRAS notification program, “[T]he published results of a particular safety study may not be sufficient to demonstrate the common knowledge element if the study raises safety questions that require additional data to be resolved” (62 FR at 18943).  Similarly, if fundamental questions exist regarding such a study’s basic ability to resolve or address relevant safety questions, that study is likely to be insufficient to demonstrate general recognition of safety.
Where an existing GRAS determination does not apply, we note that a separate determination of GRAS status for the use of the food substance would depend both on technical evidence of safety and on general recognition of safety (in other words, this evidence being both generally available and accepted by qualified experts).  It is prudent to consult with us on any potential view that the available data and information could form a basis for a determination of GRAS status of a food substance that involves significant manufacturing process changes, including but not limited to those involving nanotechnology or other emerging technologies.  Suchtechnologies could be so new as to preclude a consensus among experts that the use of a food substance manufactured using that technology is safe, thus precluding a determination that the use of the food substance is GRAS.  Therefore, it is likely that premarket review and approval of the food substance on a case-by-case basis by the agency is warranted.  

V. References

We have placed the following references on display in the Division of Dockets Management, Food and Drug Administration, 5630 Fishers Lane, rm. 1061, Rockville, MD 20852. You may see them at that location between 9 a.m. and 4 p.m., Monday through Friday.   As of November 16, 2011, FDA had verified the Web site address for the references it makes available as hyperlinks from the Internet copy of this guidance, but FDA is not responsible for any subsequent changes to Non-FDA Web site references after November 16, 2011.
  1. FDA. 2007. Nanotechnology Task Force Report 2007.
  2. FDA. Draft Guidance for Industry- Considering Whether an FDA-Regulated Product Involves the Application of Nanotechnology.
  3. FDA. Guidance for Industry - Questions and Answers About the Petition Process.
  4. FDA. Guidance for Industry - Preparation of Food Contact Notifications: Administrative.
  5. FDA. Guidance for Industry - Frequently Asked Questions About GRAS.
  6. FDA. Guidance for Industry - Recommendations for Submission of Chemical and Technological Data for Direct Food Additive Petitions.
  7. FDA. Guidance for Industry - Color Additive Petitions. FDA Recommendations for Submission of Chemical And Technological Data On Color Additives For Food, Drugs Or Cosmetics
  8. FDA. Guidance for Industry - Preparation of Premarket Submissions for Food Contact Substances: Chemistry Recommendations.
  9. FDA. Guidance for Industry- Estimating Dietary Intake of Substances in Food.
  10. FDA. Guidance for Industry and Other Stakeholders - Toxicological Principles for the Safety Assessment of Food Ingredients. Redbook 2000. Table of Contents.
  11. FDA. Preparation of Food Contact Notifications for Food Contact Substances: Toxicology Recommendations.
  12. Lehigh University (2004, April 29). Nanogold Does Not Glitter, But Its Future Looks Bright. ScienceDaily. Accessed and printed March 1, 2010 disclaimer icon.
  13. Scientific Committee on Emerging and Newly Identified Health Risks. 2009. Risk Assessment of Products of Nanotechnologies.
  14. FDA.  2004. Agency Response Letter GRAS Notice No. GRN 000138.
  15. Principles for Regulation and Oversight of Emerging Technologies, March 11, 2011.
  16. Policy Principles for the U.S. Decision-Making Concerning Regulation and Oversight of Applications of Nanotechnology and Nanomaterials, June 9, 2011.
  17. European Food Safety Authority.  2009. Scientific Opinion: The Potential Risks Arising from Nanoscience and Nanotechnologies on Food and Feed Safety. The EFSA Journal.  958, 1-30.
  18. Food Safety Authority of Ireland. 2008. The relevance of Food Safety of Applications of Nanotechnology in the Food and Feed Industries.
  19. FDA.  1996.  Guidance on Consultation Procedures. Foods Derived From New Plant Varieties.
  20. FDA.  2003.  Agency Response Letter GRAS Notice No. GRN 000121.
  21. FDA.  2006.  Agency Response Letter GRAS Notice No. GRN 000187.
  22. FDA.  Inventory of Effective Food Contact Substance (FCS) Notifications. Web site for users to launch a database.
  23. FDA.  Threshold of Regulation Exemptions.
  24. FDA.  GRAS Notice Inventory. Web site for users to launch GRAS Notice Inventory. 

Appendix 1.  Examples of FDA’s Previous Consideration of Changes in Manufacturing Process

Below we provide three specific examples where the Agency has already reconsidered the regulatory status of the use of a food substance and concluded that a significant change in manufacturing process did not negatively affect safety.  The examples below are intended to illustrate how changes to a food manufacturing process factor into our consideration of effects on identity, safety, and/or regulatory status of resultant food substances.  We intend to update these examples as the agency gains additional experience evaluating food substances, including those manufactured using nanotechnology.

A. Carrageenan (21 CFR 172.620)

Under 21 CFR 172.620, carrageenan is described as a “refined hydrocolloid that is prepared by aqueous extraction from specific red seaweeds.”  Traditionally, carrageenan had been produced by extracting the carrageenan (from one of eight red seaweeds listed in the regulation) and filtering the extract to remove cellulose and other substances.  In the late 1970s, a manufacturing change that was developed resulted in less complete removal of cellulose and a less refined product.
Due to limited information about this new process, we initially requested that a new food additive petition be submitted.  Upon review of the modified manufacturing process, we determined that the process used to produce the less refined carrageenan met the aqueous extraction requirement in its regulation, the new material conformed to the food ingredient specifications for carrageenan, and the process was as effective at removing impurities normally found in seaweed as the original manufacturing method.  We concluded that the only significant difference between the new “carrageenan” and traditional carrageenan is that the former contains more cellulose compared to traditionally refined carrageenan.  We did not consider the additional cellulose in carrageenan to be a safety concern and concluded that the new product still complied with the regulation for carrageenan.  In light of this conclusion, we rescinded our earlier request for a food additive petition.

B. Xanthan Gum (21 CFR 172.695 and GRAS Notice No. GRN 000121)

Xanthan gum is approved as a food additive for use as a stabilizer, emulsifier, thickener, suspending agent, bodying agent, and foam enhancer in foods (21 CFR 172.695). The regulation specifies that xanthan gum is purified by recovery with isopropyl alcohol (21 CFR 172.695(a)). In GRAS Notice No. 000121, a manufacturer determined that xanthan gum purified by recovery with an alternative solvent, ethyl alcohol, is GRAS for certain uses. In our letter responding to the GRAS notice (Ref. 20), we referred to the xanthan gum prepared by the alternative manufacturing process as "xanthan gum (ethanol precipitate)." We noted that the modified manufacturing process for xanthan gum (ethanol precipitate) does not comply with the specifications listed in 21 CFR 172.695; in order for xanthan gum (ethanol precipitate) to comply with 21 CFR 172.695, that food additive regulation would need to be amended to include purification of xanthan gum by recovery with ethyl alcohol. However, we had no questions about the manufacturer's determination that the specified uses of ethanol precipitate of xanthan gum are GRAS. The manufacturer was later informed by FDA that the common and usual name "xanthan gum" is permitted because xanthan gum (ethanol precipitate) is chemically indistinguishable from the food additive xanthan gum.

C. Tartaric Acid (21 CFR 184.1099 and GRAS Notice No. GRN 000187)

L (+) tartaric acid is affirmed as GRAS for use as a food ingredient (21 CFR 184.1099).  The regulation specifies that tartaric acid is obtained as a by-product of wine manufacture (21 CFR 184.1099(a)).  In GRAS Notice No. 000187, a manufacturer concluded that L (+) tartaric acid produced by an alternative manufacturing process (i.e., by the conversion of maleic anhydride to tartaric acid through the enzymatic action of the enzyme cis-epoxisuccinate hydrolase, contained in immobilized Rhodococcus ruber cells) is GRAS for the same use as described in 21 CFR 184.1099.  In our letter responding to the GRAS notice (Ref. 21), we noted that the L (+) tartaric acid described in GRN 000187 substituted for the uses of tartaric acid prepared as described in 21 CFR 184.1099 and, thus, total daily intake of tartaric acid was not expected to change from the current level.  We also noted that L (+) tartaric acid produced by the alternative method is chemically identical to the tartaric acid affirmed as GRAS in 21 CFR 184.1099 and meets the specifications for tartaric acid in the Food Chemical Codex (FCC), 5th ed., 2003.  We had no questions about the manufacturer’s determination that L (+) tartaric acid produced by the alternative manufacturing process is GRAS for the same use as described in 21 CFR 184.1099.

Appendix 2.  Descriptions of the Principal Regulatory Submissions for Food Substances


A. Petition Process for Premarket Approval of a Food Additive

Our implementing regulation for the food additive petition process is in 21 CFR 171.1.  In general, a food additive petition includes information such as:
  • The name and pertinent information about the identity of the food additive (including chemical identity and composition;  physical, chemical, and biological properties; and specifications prescribing the minimum content of the desired component(s) and identifying and limiting the reaction byproducts and other impurities) (21 CFR 171.1(c)A);
  • Information about the manufacturing process and any person other than the petitioner who performs any manufacturing, processing, and packing operations for the additive (21 CFR 171.1(c)A and 21 CFR 171.1(j));
  • The amount of the food additive proposed for use and the purposes for which it is proposed (21 CFR 171.1(c)B);
  • Data establishing that the food additive will have the intended physical or other technical effect (21 CFR 171.1(c)C); and
  • Full reports of investigations made with respect to the safety of the food additive (21 CFR 171.1(c)E).
If we find that the data and information submitted in a food additive petition establish that the food additive will be safe under the conditions of its intended use, we authorize the use of the food additive through a regulation established in 21 CFR.  The regulation establishes the conditions under which the additive may be safely used (including specifications as to the particular food or classes of food in or on which such additive may be used, the maximum quantity which may be used or permitted to remain in or on such food, the manner in which the additive may be added to or used in or on such food), the function(s) for which the food additive may be added to or used and, as needed, any specific labeling requirements associated with the addition or use of the food additive.  In establishing the regulation, we rely on the information in the food additive petition as well as other available data and information, and include memoranda documenting that review in the administrative record of the petition; however, the regulation reiterates or describes only a small fraction of the information in the administrative record of the petition.
In most cases, our regulations describe the identity of the food additive and the manufacturing process for the food additive.  The degree of detail for these descriptions varies.  As one example, the regulation for carrageenan (21 CFR 172.620) specifies that carrageenan is the refined hydrocolloid prepared by aqueous extraction from specifically named species of red seaweed.  As another example, the regulation for xanthan gum (21 CFR 172.695) specifies that xanthan gum is a polysaccharide gum derived from Xanthomonas campestris by a pure-culture fermentation process and purified by recovery with isopropyl alcohol; the regulation for xanthan gum further specifies that xanthan gum contains D-glucose, D-mannose, and D-glucuronic acid as the dominant hexose units and is manufactured as the sodium, potassium, or calcium salt.
We have provided guidance to industry on administrative aspects of a food additive petition as well as on the preparation of data and information regarding the identity, manufacturing process, technical effect, and evaluation of safety of a food additive (Refs. 3, 6, 7, 9, and 10).

B. Premarket Notification Program for a Food Contact Substance

Our implementing regulations for the premarket notification program for a FCS are in 21 CFR 170.100 through 21 CFR 170.106.  In general, a notification for a FCS includes data and information analogous to those that would be submitted in a food additive petition (see section VII.A in Appendix 2 of this document).  However, some of the data and information that would be submitted in a premarket notification for a FCS are different in that they relate to the fact a FCS is not intended to be directly added to food; rather, it is the case that some amount of a FCS may migrate to food.
An FCN is effective only for the manufacturer, substance, and intended use identified in the notification.  Any person wishing to rely on an FCN will need to determine that the FCS being marketed has been manufactured or supplied by the manufacturer identified in the FCN and is being used under the conditions that are the subject of the FCN.
We have provided guidance to industry on administrative aspects of a food contact notification as well as on the preparation of data and information regarding the identity, manufacturing process, technical effect, and evaluation of safety of a FCS (Refs. 4, 8, 9 and 11).  Currently, we provide an Inventory of Effective Food Contact Substance Notifications on our Web site (Ref. 22).  This inventory is not required by statute or regulation and should not be presumed to contain all information relevant to identity of the notified substance.  In establishing a listing for a specific FCS in the Inventory of Effective Food Contact Substance Notifications, we use the information in the FCN; however, that listing reiterates or describes only a small fraction of the information in the FCN. By contrast the notification is required by statute to include all information relevant to the safety determination for the food contact substance.

C. “Threshold of Regulation” Program for a Substance Used in a Food Contact Article

Our implementing regulation for the Threshold of Regulation (TOR) process is in 21 CFR 170.39.  Under 21 CFR 170.39, a substance used in a food-contact article (e.g., food packaging or food-processing equipment) that migrates, or that may be expected to migrate, into food will be exempted from regulation as a food additive because it becomes a component of food at levels that are below the threshold of regulation if the substance satisfies certain criteria relating to:
  • Its potential carcinogenicity;
  • The estimated dietary exposure to the substance;
  • Its lack of technical effect in or on the food to which it migrates; and
  • Its lack of significant adverse impact on the environment.
In general, a request for an exemption request under the TOR program includes information such as:
  • Chemical composition;
  • Detailed information on the conditions of use;
  • Validated migration data;
  • Information on either the amount of the food substance used in the manufacture of the food-contact article or on the residual level of the food substance in the food contact article; and
  • An analysis of existing toxicological information on the food substance and its impurities. 
We respond by letter to a person who requests an exemption under the TOR program.  Currently, we maintain a list of exemptions under 21 CFR 170.39 on our Web site (Ref. 23).

D. Program to Notify FDA of a Determination That a Use of a Substance is Generally Recognized as Safe

Our implementing regulations regarding the criteria for eligibility for classification of the use of a substance as GRAS are in 21 CFR 170.30.  Regulations identifying GRAS conditions of use for certain substances are in Part 182 and regulations affirming the GRAS status of the use of some food ingredients and food contact substances are in 21 CFR Parts 184 and 186, respectively.  Importantly, the GRAS regulations do not apply to the use of a substance that meets the statutory definition of a color additive (see section II.B of this document).
In 1997, we proposed to establish a voluntary notification procedure whereby you may notify us of your determination that a particular use of a substance is GRAS (62 FR 18938; April 17, 1997).  In 1998, we started accepting GRAS notices under the framework of the proposed rule (Ref. 5).  In general, under that framework a GRAS notice includes information such as:
  • The applicable conditions of use of the notified substance;
  • Detailed information about the identity of the notified substance, including the method of manufacture and specifications for food-grade material;
  • Information on any self-limiting levels of use; and
  • A detailed summary of the basis for the notifier's determination that a particular use of the notified substance is not subject to the premarket approval requirements of the Act because such use is GRAS.
We evaluate whether each submitted notice provides a sufficient basis for a GRAS determination for the intended use and whether information in the notice or otherwise available to us raises issues that lead us to question whether the intended use of the substance is GRAS. Following this evaluation, we respond to the notifier by letter.  Our letter summarizes the notifier’s basis for determining that the intended use of the notified substance is GRAS, including information about the identity of, and manufacturing process for, the notified substance. 
Currently, we provide a summary of information about GRAS notices in our GRAS Notice Inventory (Ref. 24).   The GRAS Notice Inventory provides links to information such as the name of the substance, the name and address of the person who made the GRAS determination, and the letter we sent in response to the notice.
As is the case for a food additive, a GRAS regulation reiterates or describes only a small fraction of the information in a GRAS affirmation petition.  Likewise, information in our response to a GRAS notice describing a notified substance reiterates or describes only a small fraction of the information in the GRAS notice.

E. Petition Process for Listing a Color Additive

Our implementing regulation for the color additive petition process is in 21 CFR 71.1.  In general, a color additive petition includes information similar to that submitted in a food additive petition (see section VII.A in Appendix 2 of this document).
If we find that the data and information submitted in a color additive petition establish that the color additive will be safe and suitable under the conditions of its intended use, we list the use of the color additive through a regulation established in 21 CFR (21 CFR 70.42(a)).  The regulation may list the color additive for use generally in or on foods, or may prescribe the conditions under which the color additive may be safely used (including specifications as to the particular food or classes of food in or on which such color additive may be used; the maximum quantity of any straight color or diluent that may be used or permitted to remain in or on such food; and the manner in which such color additive may be added to or used in or on such food).   In establishing the regulation, we rely on the information in the color additive petition as well as other available data and information, and include memoranda documenting that review in the administrative record of the petition; however, the regulation reiterates or describes only a small fraction of the information in the administrative record of the petition.
In most cases, our regulations describe the identity of the color additive and the manufacturing process for the color additive.  The degree of detail for these descriptions varies.  As examples:
  • The regulation for astaxanthin (21 CFR 73.35) states the chemical name for astaxanthin and describes its color through its spectral properties (absorption maximum wavelength 484-493 nanometers in chloroform), but is silent on the manufacturing process. 
  • The regulation for dehydrated beets (beet powder) (21 CFR 73.40) describes the color of the additive as dark red powder and describes the manufacturing process as dehydrating sound, mature, good quality, edible beets
  • The regulation for ultramarine blue (21 CFR 73.50) describes the color additive as a complex sodium aluminum sulfo-silicate (including an approximate chemical formula) that is a dark blue pigment. In describing the manufacturing process, the regulation specifies that ultramarine blue is obtained by calcining a mixture of kaolin, sulfur, sodium carbonate, and carbon at temperatures above 700 °C, and that sodium sulfate and silica may also be incorporated in the mixture in order to vary the shade.
We have provided guidance to industry on administrative aspects of a color additive petition as well as on the preparation of data and information regarding the identity, manufacturing process, technical effect, and evaluation of safety of a color additive (Refs. 3, 6, 7, 9 and 10).

This guidance has been prepared by the Office of Food Additive Safety in the Center for Food Safety and Applied Nutrition at the U.S. Food and Drug Administration.
2 An end user is a person who uses an ingredient or a FCS in the manufacture of a food product, and who may or may not manufacture the ingredient or FCS.
3 For the purpose of this document the term nanometer range refers to any particle size between 1 nanometer and micrometer.
4 Nanotechnology allows scientists to work on the scale of molecules to create, explore, and manipulate the biological and material worlds measured in nanometers, one-billionth of a meter.  In July of 2007, we issued a report prepared by our Nanotechnology Task Force (Ref. 1).  The term is perhaps most commonly used to refer to the intentional manipulation, manufacture or selection of materials that have at least one dimension in the size range of approximately 1 to 100 nanometers.  However, there currently are questions as to whether size alone should be the determining factor for the definition, or whether additional criteria such as shape, charge, the ratio of surface area to volume, or other physical or chemical properties should be included in a definition.
At this time, we have not established a formal definition of “nanotechnology,” “nanoscale” or related terms.  As discussed in the Task Force report, we believe it is appropriate to take into account the potential importance of material size and the evolving state of the science.  However, while one definition for “nanotechnology,” “nanoscale material,” or a related term or concept may offer meaningful guidance in one context, that definition may be too narrow or broad to be of use in another.  As we learn more about the interaction of nanoscale materials with biological systems and generalizable concepts that can inform our judgment, it may be productive to develop formal, fixed definitions, appropriately tailored to the regulation of nanoscale materials in products we regulate.
In the absence of a formal definition, when considering whether a FDA-regulated product contains nanomaterials or otherwise involves the application of nanotechnology, FDA will ask: (1) whether an engineered material or end product has at least one dimension in the nanoscale range (approximately 1 nm to 100 nm); or (2) whether an engineered material or end product exhibits properties or phenomena, including physical or chemical properties or biological effects, that are attributable to its dimension(s), even if these dimensions fall outside the nanoscale range, up to one micrometer.  Once finalized, the agency intends to apply these considerations broadly to all FDA-regulated products, including food substances (2011 draft guidance; Ref. 2).
5 See, e.g., sections 301(a) through (c) and section 303(a).
6 The term “safe,” as used in section 201(s) and in the sections relevant to this document (409 and 721) refers to the health of man or animal (section 201(u) of the Act).
7 U.S.C. Title 21 Section 379e
Alloimmunization is an immune response generated in an individual or strain of one species by an alloantigen from a different individual or strain of the same species (Dorland's Online Medical Dictionary for Health Consumers. © 2007.)   
As noted in the 2011 draft guidance, in considering applications of nanotechnology, we distinguish between products that have been engineered to contain nanoscale materials or involve the application of nanotechnology from those products that contain incidental or background levels of nanomaterials or those that contain materials that naturally occur in the nanoscale range.  FDA recognizes that conventionally manufactured food substances can sometimes include particles with size distributions that extend into the nanometer range. This draft guidance is not intended to bring into question the regulatory status of such products to the extent that they may have already been determined to be GRAS or approved in response to a food additive petition, color additive petition, or food contact notification. However, as noted in the text, intentional alterations in particle size distribution on the nanometer scale can sometimes be significant manufacturing changes. 
10 These food substances include food contact substances that are the subject of a food additive regulation.
11 As explained in section II.C. above, there is no GRAS provision for color additives and all uses of color additives must be approved as safe by FDA prior to marketing.  The reference to “food substance” here does not include food ingredients that are used as color additives.
12 See generally footnote 9 above.